RULETEAM CONNECTION TECHNOLOGY (SHENZHEN) CO.,LTD
To offer best product & service for all customer! To become stronger by team's widsom, to grow up together for same benefit!
Add to Cart
1, Detailed part information as below
1. Basic information:
2. Electrical characteristic:
3. Mechanical characteristic:
Other information please kindly check the following picture.
2, Introduction for this series products
Please kindly notice that the C3030 series product, you can buy it as a set, then we will offer you reasonable price.
| C3030 series product | ||
| Terminal | C3030F-T-A and C3030M-T | |
| Connector | Male housing | C3030HF-NP & C3030HF-2XNP &C3030HFA-2XNP |
| Female housing | C3030HM-NP & C3030HMA-NP &C3030HM-2XNP & C3030HMA-2XNP | |
|
Wafer |
Vertical type | C3030WV-F-NP &C3030WV-F-2XNP |
| Right angle type | C3030WR-F-XP & C3030WR-F-2XNP | |
3, Corresponding engineering drawing & testing report
Environmental Performance And Others
| Test Description | Procedure | Requirement | |
| 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) |
| 6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) |
Appearance No Damage. Contact Resistance 20mΩ (Max.) |
| 6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) | |
| 6-4 | Humidity |
Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) |
Appearance No Damage. Contact Resistance 20mΩ (Max.) Insulation Resistance 100MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 |
Mechanical Performance
| Test Description | Procedure | Requirement | ||
| 5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw connectors at the speed rate of 25±3mm / minute. | Refer to paragraph 7 | |
| 5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) | AWG#20 | 6.0kgf (Min.) |
| AWG#22 | 4.0kgf (Min.) | |||
| AWG#24 | 3.0kgf (Min.) | |||
| 5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 1.50kgf (Max.) | |
| 5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. | 2.50kgf (Min.) | |
| 5-5 | Pin Retention Force | Apply axial push force at the speed rate of 25±3mm / minute | 1.50kgf (Min.) | |
| 5-6 | Latch Yield Strength |
Mate connectors and pull apart until both latches break at the speed rate of 25±3mm / minute |
7.00kgf (Min.) | |
| 5-7 | Panel Mount Retention Force | Insert the housing into panel cut out, barbs break at the speed rate of 25±3mm / minute. |
Single Row(W-W) 8.0kgf (Min.) Dual Row(W-W) 16.0kgf (Min.) |
|
| 5-8 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 20mΩ (Max.) | |
4, Our main customer and partner
It's no doubt that you can trust us like the world class 500 enterprise. It's sure that we will regard you as well as them, to support our best service and products. So please contact me directly, we are waiting for you. Come on!