1, Product specification
| Basic size information |
| Color |
white |
| Pitch |
1.0mm |
| Terminal insulation O.D. |
0.60mm(max) |
| Terminal material |
phosphor bronze |
| Finish terminal |
gold-flash |
| Position |
30 pins |
| Wire range |
AWG#30 to #34 |
| |
| Electrical properties |
| Current Rating |
1A AC, DC |
| Voltage Rating |
200V AC, DC |
| Contact Resistance |
40mΩ Max |
| Insulation Resistance |
100mΩ |
| Withstanding Voltage |
500V AC/minute |
| |
| Mechanical properties |
| Temperature range |
-25℃ to 85 ℃ |
2, Related drawing and report
The below engineering drawing and testing report is for your reference, it's no doubt that it can help you to get right parts for your device.
|
5. Mechanical Performance
| Test Description |
Procedure |
Requirement |
| 5-1 |
Actuator Insertion & Withdrawal Force |
Insert and withdraw connectors at the speed rate of 25±3mm / minute. |
Refer to paragraph 7 |
| 5-2 |
Crimping Pull Out Force |
Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) |
AWG#30 |
0.8kgf (Min) |
| AWG#32 |
0.5kgf (Min) |
| AWG#34 |
0.3kgf (Min) |
| 5-3 |
Terminal Insertion Force. |
Insert the crimped terminal into the housing. |
0.50kgf (Max.) |
| 5-4 |
Terminal/Housing Retention Force. |
Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. |
0.50kgf (Min.) |
| 5-5 |
Pin Retention Force |
Apply axial push force at the speed rate of 25±3mm / minute |
0.40kgf (Min.) |
| 5-6 |
Durability |
When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. |
Contact Resistance 80mΩ (Max.) |
| 5-7 |
Vibration |
Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes.
(Based upon MIL-STD-202 Method 201A)
|
Appearance No Damage.
Contact Resistance 80mΩ (Max.)
Discontinuity 1 μsec.(Max.)
|
| 5-8 |
Physical Shock |
490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) |
|
|
6. Environmental Performance And Others
| Test Description |
Procedure |
Requirement |
| 6-1 |
Temperature Rise |
Carrying rated current load.(Based upon UL 498) |
30℃(Max.) |
| 6-2 |
Heat Resistance |
85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) |
Appearance No Damage.
Contact Resistance 80mΩ (Max.)
|
| 6-3 |
Cold Resistance |
-25±3℃,96 hours (Based upon JIS C0020) |
| 6-4 |
Humidity |
Temperature: 40±2℃
Relative Humidity : 90~95%
Duration: 96 hours
(Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B)
|
Appearance No Damage.
Contact Resistance 80mΩ (Max.)
Insulation Resistance 10MΩ (Min.)
Dielectric Withstanding Voltage Must meet 4-3
|
| 6-5 |
Temperature Cycling |
5 cycles of:
a) -55℃ 30 minutes
b) +85℃ 30 minutes
(Based upon JIS C0025)
|
Appearance No Damage.
Contact Resistance 80mΩ (Max.)
|
| 6-6 |
Salt Spray |
Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) |
| 6-7 |
SO2 Gas |
24 hours exposure to 50±5ppm.
SO2 gas at 40±2℃.
|
| 6-8 |
NH3 Gas |
40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| 6-9 |
Solderability |
Soldering Time: 5±0.5 sec.
Solder Temperature: 245±5℃
|
Solder Wetting 95% of immersed area must show no voids, pin holes |
| 6-10 |
Resistance to Soldering Heat |
When reflowing
Refer to paragraph 8
Solder iron method
Soldering Time: 5±0.5 sec.
Solder Temperature: 370℃ ~ 400℃
|
Appearance No Damage. |
7. Actuator Insertion/Withdrawal Force
[Unit : kgf]
| Circuits |
At Initial |
| Insertion (Max.) |
Withdrawal (Min.) |
| 20 |
2.60 |
0.60 |
| 30 |
4.00 |
0.76 |
|
3, The product application scope
This product are widely fixed in household appliance, computer, telecommunication device. Our parts are accepted by famouse and international company like TPV, Emerson, Amphenol Corporation, LuXshare, BYD etc because of its' low defective rate. And the all products are approved by REACH, UL, RoHS internation standard. Some parts are halogen free to protect the green world.
4, Our intimate service for you
We can offer you all kind of intimate service like prompt samples, fast delivery and flexible payment way.
